Mars CASHFLOW 126 Instrukcja Użytkownika

CASHFLOW® 126 and CASHFLOW® 1294-WAY and 8-WAY SELECTORSUSER GUIDE25859 G3 705707044

INSTALLATIONInstalling or removing the CashFlow®® product from your machine can be done byfollowing these simple instructions. + When installing the

CF 126 Top Entry Installation+ When mounted into a short channel the product must be fully assembled and ready for use,with only the machine interface

CashFlow® 129 System InstallationThe system consists of a channel, Y-chute, CashFlow® 129 validator, 8-way separator,manifold and tube collar plate. T

Removal of Manifold and Collar Plateq The manifold is supported in position by four lugs which slot into the side plates ofthe channel. It is retained

ACCEPTANCE AND ROUTINGWhen the product is successfully mounted you will need to confirm that it is set upcorrectly to accept good coins/tokens and dir

PRODUCT FEATURESThe CashFlow® 126 and CashFlow® 129 products have the flexibility to change certainsettings such as varying the coin-set that it handl

CONFIGURATIONValidator Interface ConnectorThe interface to the validator from the machine is exactly the same as those which applyto the MS/ME series

Assembling a 22-Way Routing PlugWhile the links are readily inserted into the routing plug by hand without specialist tools,care is needed to ensure t

Coin and token values as shown on the coin set label are expressed in the following textas channels. The relative positions of these channels and coin

Route Inhibit ConnectorThe function of the route Inhibit Connector is to signal when specific exits, external to theproduct, are in a “Full” condition

Published by :Mars Electronics InternationalEskdale RoadWinnersh TriangleWokingham, Berkshire, RG41 5AQUnited Kingdom.Internet: http://www.meiglobal.

Using the Rotary Data Switch and ConfigurationSwitchesRotary Data SwitchThe rotary data switch is used in conjunction with theconfiguration switches.

Product Configuration - Inhibiting coins or tokensExample:- To inhibit channel 2 (the 5p coin) on your validator followthese simple steps.1. Switch Va

Product Configuration - Enabling coins or tokensExample:- To enable channel 2 (the 5p coin in this instance) on yourvalidator follow these simple step

Product Configuration - teaching a new token,channel 0Example:- To Teach a Token (with standard window limits) into channel0 follow these simple steps

Product Configuration - teaching a new token,channel 1Example:- To Teach a Token (with standard window limits) into channel1 follow these simple steps

Product Configuration - Selecting a pre-programmed token group to be usedin channel 014 token groups are already programmed into the product. This fe

Product Configuration - Selecting a pre-programmed token group to be usedin channel 114 token groups are already programmed into the product. This fea

Product Configuration - Changing the machine output modeTo change the coin output interface to Fixed Binary Coded Output(BCO) use these simple steps.

MAINTENANCE+ The practical maintenance that can be carried out is limited to cleaning the areas of thevalidator that the coins travel through, and the

Product RevisionThe revision level of the 126/129 product can be confirmed from a label on the left side ofthe product. There are two levels of digits

CONTENTSSafety Summary 1 Product Identification 3Installation 6Acceptance & Routing 10Product Features 11Configuration 12Maintenance 21Product

PRODUCT SUPPORTIn addition to the MEI offices around the world an international network of Distributors andApproved Service Centres can offer you tech

Helping you deliver YOUR MEI REPRESENTATIVE

iv ©, Mars, Inc., 1998CashFlow® 126 and CashFlow® 129 selectors User Guide

SAFETYWarningBefore cleaning, servicing, removing or replacing CashFlow® units, ALWAYS SWITCHOFF or ISOLATE the ELECTRICITY SUPPLY to the host machine

DOCUMENT GUIDEThis document is for field engineers using the CashFlow® 126 andCashFlow® 129 products produced by Mars Electronics International (MEI)

PRODUCT IDENTIFICATIONMars Electronics International (MEI) has manufactured coin mechanisms compatible withgaming and amusment machines for a number o

The entry bezel and the Y-chute options can be used with either the CashFlow® 126system or CashFlow® 129 system. The CashFlow® 126 can be supplied fo

The electrical connections and interfaces to each variant of CashFlow® 126 andCashFlow® 129 are identical, and are found in the same locations.(A) Ma